Vinyl Siding Installation and How to Install Vinyl Siding

0
1170
Vinyl Siding Installation

How to install Vinyl siding: an Ultimate guide for vinyl siding Installation.

Vinyl siding is a very popular material among homeowners for many reasons including its durability, longevity and the low maintenance required to keep it in good condition. In addition, there are a lot of color and model options on the market. We will offer you all the relevant information about how to install vinyl siding. Here we have discussed vinyl siding installation in very easy steps.

Vinyl Siding Installation In 8 Easy Steps:

Vinyl siding installation is one of the biggest and easy ways to make the walls beautiful of your home. To install Vinyl siding is fast, simple, and one of the most cost-effective ways to cover the look of your home. Before you start, you need some skills, such as reading the tape measure correctly, using a box knife or tin cut, reading the level, and manipulating the chalk line. All of these skills are fairly basic and relatively easy to learn. People often ask how to install vinyl siding and looking for some expert advice.

Let’s discuss vinyl siding installation in 8 different steps to make installation easy. Once you have determined that you have the right skill set for your job, you can start to install vinyl siding.

Vinyl Siding Installation
Vinyl Siding Installation

Step 1 On How to Install Vinyl Siding -Measure The Space

Now, the process doesn’t have to be accurate to square inches. In fact, you’ll probably want to overestimate a bit to buy enough material. Measure the height and width of all walls you want to cover with vinyl siding.

Multiply the width and height of each wall and add them together.

Now go back and calculate the area of ​​each door and window on each side and round it. In this example, we always want to minimize the uncovered area and maximize the covered area to get enough material.

Subtract the door and window area from the total wall space covered.

Step 2 on How to Install Vinyl Siding -Trim Measurement

The sides and top of the doors and windows are trimmed with J-trim. You can also use it along the bottom of a window sill, but it’s less common because many homeowners don’t like the look. Add up all sides and top dimensions for all doors and windows.

At the top of the wall and below the window frame, there is a trim section at the top of the wall, so measure everything and add dimensions.

There is a starter strip at the bottom of each wall. Measure all these lengths and add them together.

All corners and front can be trimmed with vinyl siding. Alternatively, you can continue painting, but converting it to vinyl siding is the best way to look good and protect your house for a long time. Measure the length of each piece and make a note somewhere so you don’t have to re-measure it later. Measure the entire area of ​​your underneath part of the edge and make sure you count the number of these edges you have. Then add these measurements. 

Vinyl Siding Installation
Vinyl Siding Installation

Finally, add all the trim measurements together, add another 10-15% and record that number for purchase.

Step 3 to Install Vinyl Siding -Estimate The Needs Of Other Materials

After estimating your total vinyl siding and trim requirements, you should consider your accessories. Also, if you want to add a layer of rigid foam board below, you need to buy the same amount of rigid foam as the area of ​​the wall and deduct the area that occupies the door and window space.

Step 4 in How to Install Vinyl Siding -Buy All The Materials You Need

Take a list of estimated measurements to your local hardware store. Choose the vinyl siding style and color you need and order enough material to cover everything on the list.

Depending on the amount of material you order, many home improvement centers will deliver your order to your home for a small fee. Delivery is highly recommended unless you have a truck or other vehicle that can easily load and unload long vinyl siding.

Step 5 in Vinyl Siding Installation -Install Trim Piece

Measure and cut the top and bottom of all walls and the trim areas around the doors and windows. You can create the cut using a box knife or a sharp cut.

Vinyl Siding Installation
how to install vinyl siding

Install the trim along the edges, corners, bottom, and top of all walls. The trim provides the framework for the vinyl siding and holds it in place at the ends, top, and bottom of each wall. Therefore, to mark the position of the starter strip just above the ground level, you need to use the level and choke line on the top of the exposed foundation wall. This gives you a level pattern that should follow in Vinyl Siding Installation

Step 6 On How to Install Vinyl Siding -Rigid Foam Installation (Optional)

The rigid foam must be installed under vinyl siding, so it must be installed first for home use.

Use a box knife or scissors to cut the pieces to fit the wall. Most installers use a ¼ ”thick blue foam that is easy to cut.

Attach the foam using deck screws or roof nails. Screws are usually faster on a cordless drill than on the hand.

Keep the foam approximately 1 inch away from all trim parts for easy vinyl siding installation.

Step 7-Install Vinyl Siding

Select the wall where you want to start the installation and start from the bottom corner. Fit the bottom edge of the siding into the starter strip so that it stands upright along the wall. Push the starting edge into the channel along the side of the corner trim. Install one fastener every 8-10 inches along the strip of nails at the top of the vinyl siding.

Add pieces end to end and stack at least 1 inch in the direction of the opposite corner of the wall. Cut the last piece so that it overlaps the previous piece and insert it into the corner trim channel. Similar to the starter strip, install the next row first, using the channel at the bottom of the nail strip at the top of the first row of Vinyl Siding Installation .

Vinyl Siding Installation
how to install vinyl siding

Continue to the top of the wall. In most cases, the top row should be cut to the height so that the cut edges fit in the top trim of the wall.

Step 8 in Vinyl Siding Installation -Manipulate Around Doors and Windows

If necessary, cut the piece to fit around the door or window. When going up or down a window or door, you probably need to cut the height in the area of ​​the opening. Therefore, the edges fit neatly in the wall top trim. In these cases, the notch is suitable for cutting.

How to install Vinyl Siding
How to install Vinyl Siding

After completing the same process for all walls of the house, you can sit back and relax and enjoy the beauty you created.

LEAVE A REPLY

Please enter your comment!
Please enter your name here